Quote & Schedule

What're your thoughts about How to Install a Bathtub?

Mounting a bathtub isn't precisely rocket science, however it does call for solid plumbing, carpentry, as well as occasionally, tiling skills. Replacing an old tub with a brand-new one is likewise a moderately challenging job. If the old tub is easily accessible, the job can relocate quickly; if you need to open up a wall to eliminate the old bathtub and place the brand-new bathtub, the task is a lot harder. In either case, the project is within a house handyman's abilities, although you will need a helper to leave the old bathtub and also embeded in the brand-new one. Ensure you have certified on your own for the work and are comfortable attempting it. As opposed to employing a specialist to take control of a halfway-completed job, it is much better to consider using one prior to you start. Possibilities are you may need a specialist plumber to make tube connections.
This short article will certainly aid you mount a new bathtub in your shower room if you have actually currently purchased a new bathtub as well as do not need to change the setup of your previous water supply pipes.
Your devices as well as product list ought to make up the following:

• New Bath tub


• Hammer


• Pipeline Wrenches


• Prybar


• Shatterproof glass


• Level


• Pliers


• Flexible Wrench


• Putty Blade


• Screwdriver


• Cold Chisel


• Measuring tape


• Pipe Caps


 

Removing Old Taps

If you need to change old taps with new ones as a part of your installation, after that the first thing you should do is separate the water. After doing so, switch on the faucets to drain pipes any water staying in the system. The process of getting rid of the existing taps can be fairly problematic because of the restricted gain access to that is often the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipes to the taps. Have a cloth prepared for the staying water that will certainly originate from the pipes. As soon as the supply pipelines have been eliminated, use the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will need to quit the single faucets from turning throughout this process. As soon as the taps have actually been removed, the holes in the bath/basin will certainly have to be cleansed of any type of old sealing substance.
Before moving on to fit the new taps, contrast the pipeline connections on the old faucets to the new taps. If the old faucets are longer than the new faucets, after that a shank adapter is required for the brand-new taps to fit.

Suitable New Touches

If the tails of the new faucets are plastic, then you will certainly require a plastic port to prevent damages to the string. One end of the connector fits on the plastic tail of the tap and also the other end provides a link to the existent supply pipelines.
If you need to fit a monobloc, after that you will call for minimizing couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next, place the tap in the installing opening in the bath/basin making certain that the washing machines are in place in between the faucet as well as the sink. Secure the faucet in position with the maker supplied backnut. As soon as the tap is safely in position, the supply pipes can be attached to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with regular faucet ports. The previous type should be attached to the faucet ends initially, tightening only by hand. The supply pipelines can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been linked.

Installing the Bathtub

Using the two wooden boards under its feet, place the bathtub in the called for placement. The wood boards are handy in equally spreading the weight of the tub over the area of the boards instead of concentrating all the weight onto four little points.
The next goal is to ensure that the bathtub is leveled all round. This can be attained by inspecting the spirit level and also adjusting the feet on the bathtub up until the level reviews level.
To set up faucets, fit the bottom of the furthest adaptable tap connector to the suitable supply pipe by making a compression sign up with; after that do the very same for the various other faucet.
Activate the water and check all joints as well as brand-new pipework for leaks as well as tighten them if needed. Load the bathtub as well as also check the overflow outlet as well as the typical outlet for leaks.
Ultimately, deal with the bath paneling as explained in the maker's instruction manual. Tiling and sealing around the tub should wait until the bathtub has been utilized at the very least when as this will certainly resolve it right into its last placement.

Preparing for the Installation

First of all, the sustaining framework provided with the bathroom must be fitted (if needed) according to the maker's guidelines. Next off, fit the taps or mixer to the bathtub. When suitable the tap block, it is essential to make sure that if the tap includes a plastic washing machine, it is fitted between the bath and the taps. On a plastic bath, it is likewise practical to fit a sustaining plate under the faucets device to stop pressure on the bath tub.
Fit the adaptable tap connectors to the bottom of the two taps using 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet via the hole in the bathroom. Utilize the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bath. See to it you utilize all of the supplied washing machines.
Link the trap to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom must currently be ready to be suited its final placement.

Tiling Around the Tub

In the location where the bath fulfills the tile, it is essential to seal the accompanies a silicone rubber caulking. This is important as the fitting can relocate enough to split a rigid seal, creating the water to pass through the wall surface in between the bathroom and the tiling, causing complications with moisture and also feasible leakages to the ceiling listed below.
You can select from a range of coloured sealants to assimilate your components and installations. They are offered in tubes and also cartridges, and also are capable of securing gaps as much as a width of 3mm (1/8 inch). If you have a larger gap to load, you can fill it with twists of drenched newspaper or soft rope. Bear in mind to always fill up the bath tub with water before sealing, to permit the motion experienced when the bathtub is in use. The sealant can crack fairly early if you do not consider this activity prior to securing.
Additionally, ceramic coving or quadrant tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise conveniently offered on the marketplace. It is suggested to fit the ceramic tiles using waterproof or water resistant adhesive as well as cement.

How to Install or Replace a Bathtub

Find Your Dimensions

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

 

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

Disconnect the Water Supply and Drain Assembly

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

 

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

 

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

Cut Out the Old Tub

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

 

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

 

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

Install the New Tub

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

 

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

 

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

 

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

Secure the Tub

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

 

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

 

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

 

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

I am very taken with Installing A Bathtub and I hope you appreciated the entire entry. Those who appreciated our page plz remember to share it. I treasure reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.

Visit Page